Galvanized wire is divided into hot galvanized wire and cold galvanized wire (electric galvanized wire). Hot dip galvanizing is dipped in zinc liquid melted by heating. It has fast production speed, thick but uneven coating. The market thickness is 45g and can reach more than 300g. The color is dark, the zinc metal is consumed, and the matrix metal is formed into the entry layer, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can adhere to decades.
- The tensile strength of steel wire is high and the hardness is high. In the flattening process, the longitudinal movement resistance of steel wire per unit volume increases and the elongation decreases. The steel wire unit volume will move to the lateral resistance smaller, the width of the increase. On the contrary, the wire is easy to extend lengthwise, and its width decreases. This is the production of high steel wire hardness is easy to wide, small hardness, easy to stretch out of wide reasons. If the tensile strength deviation of steel wire is large, the hardness uniformity of steel wire strip is poor, the width difference of the billet rolled into large, will seriously affect the quality of the billet.
- For example, if you use barbed rope to circle, the cost per meter is only a few yuan, if you use other products to circle, it may be more than ten yuan or even 20 yuan, which is no doubt to increase the cost of the user again, so cattle and sheep with barbed rope is the most affordable products.
The quality of hot-dip galvanized barbed wire is only the zinc layer attached to the surface of the wire, and with the chemical reaction, the zinc layer on the surface will gradually lose its role because of the oxidation reaction, which is more prominent in the humid environment. And because the use of rusty wire after all, it is said that the quality of hot-dip galvanized barbed wire is certainly not up to the level of stainless steel barbed wire.
Iron and steel in the condition of cooling on the surface galvanized, and hot dip galvanized steel pipe in the condition of hot dip on the surface, its adhesion is strong, not easy to fall off, hot dip galvanized pipe although also rust phenomenon, but in a long period can meet the technical and sanitary requirements.
- Hot dip galvanizing is the plating of zinc layer on the surface of Angle steel, channel steel and other metals to achieve the appearance of convenience and rust prevention of metal. Hot-dip zinc processing plants use zinc tin solution to prevent corrosion on the workpiece. This new technology can extend the corrosion time by up to five times, which is usually used in outdoor construction. Because the principle of action is not the same, so the role of the workpiece is not the same. The appearance of hot dip zinc plant is only to expand the scope of action.
The main difference is carbon content. Iron has a carbon content of 2.11 percent or more, while steel has a carbon content of 2.11 percent or less. Iron-carbon alloys with carbon content of more than 2.11% are cast iron (pig iron), which are basically not malleable and cannot be drawn into wire. Secondly, the content of impurities is different, and the content of harmful impurities such as sulfur and phosphorus in steel is smaller. Wire general color key, wire color light point, white point.
If it is not packaged, then a car of blade thorn rope can not be loaded with many pieces, and it is also relatively occupied and easy to lose in the transportation process. The number of the packed blade thorn rope is 50 bundles, and the volume is reduced after hydraulic compression so that it is more convenient to load and unload, and the forklift can easily load and unload. Under normal circumstances, when exporting, the blade thorn rope will be packaged and sold, so that the volume occupied in the container is relatively small, which can be easily placed and will not occupy much place.
First, the concept is different
Post time: 09-06-22
Post time: 30-01-23- Because the bundled galvanized wire is endowed with pre-tension, so it has the excellent characteristics of low relaxation value, small stress loss, good stability after loading, not easy to deformation, no fracture, strong elasticity, ordinary steel lines and rebar is difficult to match. The use of advanced galvanized finishing process, therefore, the use of hot-dip galvanized steel wire construction, not only good anti-corrosion performance, and beautiful generous. The product has the characteristics of smooth surface, high dimensional precision, good uniformity of zinc layer and firm adhesion.
The spray blade has strong adhesion and mechanical strength, and is widely used in the isolation and protection of the boundary of grassland and railway, as well as the protection of garden apartments, units and prisons. The following Haorong for you to introduce the characteristics of spray blade rope.
- Pressure welded steel grid plate is the steel grid plate fixed by pressure resistance welding at each intersection of bearing flat steel and transverse bar, which is called pressure welded steel grid plate. Torsion torsion square steel is generally used for cross bar of pressure welded steel grid. Although they do not belong to the same variety, but in the steel lattice plate standards and performance are still the same.
Post time: 06-04-23In the electroplating tank through the current unidirectional make zinc plating on the metal surface gradually, the production speed is slow, the coating is uniform, the thickness is thin, usually only 3-15 micron, the appearance is bright, smooth, beautiful, poor corrosion resistance, generally will rust in a few months. The production process of hot wire plating mainly includes: preparation of the original plate → pre-plating treatment → hot dip plating → post-plating treatment → finished product inspection, etc. According to custom often according to plating pretreatment method.
The distance between the adjacent two thorn rope installation do not know whether you have noticed? Careful observation can find that its spacing is not the same, the thorn rope factory for customer consultation when asking the installation height of the reason.
Post time: 16-06-22There is no adhesion test of powder spraying or fluorocarbon spraying on packaged galvanized wire, but there are two points for reference: first, in sealed or air-free environment, non-metallic volatiles can corrode zinc coating; Second, zinc at higher than 230 degrees (c) will cause the matrix metal brittle. And powder spraying and fluorocarbon spraying are to be baked at a higher temperature and in a sealed environment, causing rapid corrosion of zinc, resulting in loose corrosion film resulting in coating adhesion decline, and even lead to (matrix) steel wire brittle situation may exist.
- 1, we should pay attention to the welding mesh moisture-proof: if it is just the general outdoor air humidity, do not bother. If the weather is foggy, use dry cotton cloth to wipe the bead on the welding mesh; If it rains, you should dry the water when the rain stops. Try to maintain and prolong the life of the welding mesh.
- Electrode structure: portable non – electrode, including cylinder, tube, sleeve plug. Explosive welding flux by high fever agent and additives such as metal or metal oxide powder forming technology; Commonly used medicine tube paper tube. It can also be used for different weldment and use environment, use metal pipe, etc; Plug at the end of the electrode, which is with casing welding clamping position of the match, and stop welding flux leakage from the tube.
After annealing, the wire will become soft, flexibility will increase, iron is a relatively active metal, and more active than hydrogen, so it is a good reducing agent. At room temperature, iron is not easy to react with oxygen, sulfur, chlorine and other non-metallic elements in dry air. Its production cost is lower, its use and scale are also relatively wide, and it has better protective function. Therefore, it is an important material for steel parts in strict working environment.
Sodium and magnesium contain less combustible impurities, and when extinguished, they simply glow. Galvanizing belongs to the electrochemical processing process which is widely used on the surface of steel. So it is, first of all, because zinc coating (especially after supplementary processing, such as chromate treatment and phosphating) resistance to atmosphere and water is more stable, and the galvanized process itself this is cheaper and simple.
And high quality data and production cost and production conditions are bound, so some welding screen manufacturers did not meet the requirements of this aspect, natural in this case there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.
The galvanized layer forms a special metallurgical structure that can withstand mechanical damage during transportation and use. Selection of low carbon raw materials, through wire drawing, annealing processing, soft and strong tensile resistance. Finished products coated with anti-rust oil, not easy to rust, according to customer requirements into bundles, each bundle of 1-50Kg, can also be made into U-shaped wire, broken wire, internal plastic and external hemp packaging, mainly used for binding silk, construction silk, etc.
5, according to the wire diameter thickness to adjust zinc dipping time
Post time: 07-07-22